Honeywell RTH230B kılavuz

Honeywell RTH230B
9.2 · 2
PDF kılavuz
 · 4 sayfalar
İngilizce
kılavuzHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Honeywell RTH230B için kılavuzu buradan ücretsiz görüntüleyin. Bu kılavuz termostat kategorisine girer ve 2 kişi tarafından ortalama 9.2 ile derecelendirilmiştir. Bu kılavuz aşağıdaki dillerde mevcuttur: İngilizce. Honeywell RTH230Bhakkında bir sorunuz mu var, yoksa yardıma mı ihtiyacınız var? Sorunuzu burada sorun

Yardıma mı ihtiyacınız var?

Honeywell hakkında bir sorunuz var ve cevap kılavuzda yok mu?

  • Çözümlerle ilgili güncellemeler alın
  • Sorunuzun yanıtlarını alın

Soru cevap

Soru sayısı: 0

Honeywell RTH230B, Honeywell markası altında üretilen bir termostat çeşididir. Bu termostat, evlerde veya işyerlerinde kullanılan HVAC (Isıtma, Havalandırma ve Klima) sistemlerine entegre edilmek üzere tasarlanmıştır. RTH230B, kullanıcılara ısıtma ve soğutma ayarlarını kontrol etmek için kullanışlı bir arayüz sunar. Basit bir tasarıma sahip olup, kolay kullanılabilirlik sağlar. Ayarları programlanabilir özelliklere sahiptir, bu sayede kullanıcılar isterlerse bir zaman programı oluşturabilirler. Bu sayede kullanıcılar, sistemlerini belirli zaman dilimlerinde otomatik olarak açma veya kapama özelliğine sahip olabilirler. RTH230B, enerji tasarrufu sağlamak için programlanabilir bir termostat olarak tasarlanmıştır. Bu özelliği sayesinde, kullanıcılar evde olmadıkları zamanlarda enerji tüketimini azaltabilirler. Ayrıca, hassas sıcaklık kontrolü sağlamak için bir ölçüm sensörüne sahiptir. Bu termostat, dayanıklı ve uzun ömürlü olması için kaliteli malzemeler kullanılarak üretilmiştir. Üstün yapısal özelliklere sahiptir ve mekanik veya elektrik arızaları minimum düzeyde tutmak için tasarlanmıştır. Honeywell RTH230B, HVAC sistemlerini kontrol etmek için kullanılan güvenilir bir termostattır. Kullanıcı dostu bir arayüze ve programlanabilir özelliklere sahiptir. Enerji tasarrufu sağlayan bir termostat olarak tasarlandığından, kullanıcıların evde olmadıkları zamanlarda enerji tüketimlerini azaltmalarına yardımcı olur. Kaliteli malzemelerle üretilmiş olduğu için dayanıklı ve uzun ömürlüdür.

Genel
MarkaHoneywell
ModelRTH230B
Ürüntermostatlar
Dilİngilizce
Dosya tipiKullanım kılavuzu (PDF)

Sorunuzun cevabını kılavuzda bulamıyor musunuz? Sorunuzun cevabını SSS bölümünde, Honeywell RTH230Bbaşlığı altında bulabilirsiniz.

Termostatı nereye yerleştirmek gerekir?

Termostat için en uygun yer, çoğu zaman oturma odası veya mutfak olmak üzere en çok zaman geçirdiğiniz odadır. Termostatı güneşe veya dış duvara bakmayacak şekilde yerden yaklaşık bir buçuk metre yükseğe yerleştirin.

Termostatta ölü bant ne anlama gelir?

Termostatınızda ölü bant varsa, tesisatınız 'dinlenme modunda' demektir. Termostat yalnızca fark, ayarlanan oda sıcaklığından örneğin 2˚C'den fazla saptığında çalışmaya başlar.

İdeal oda sıcaklığı nedir?

Çoğu kişiye göre ideal oda sıcaklığı, 19 ila 22 santigrat derece arasındadır.

Honeywell RTH230B kılavuzu Türk dilinde mevcut mu?

Ne yazık ki Honeywell RTH230B kullanım kılavuzuna Türk dilinde sahip değiliz. Bu kılavuz şu dilde mevcuttur: İngilizce.

Sorunuz listede yok mu? Sorunuzu burada sorun

Sonuç yok